A Simple DIY Upgrade Any Parent Can Do
Upgrading your child's ride-on car to a lithium battery sounds technical, but the TOBBI DIY Lithium Battery Replacement for 12V Kids Ride-On Cars – 12.5Ah Long Playtime Upgrade is designed for easy, tool-friendly installation. In most cases, you can complete the swap in under 15 minutes with no special skills required.
This guide walks you through the entire process so you can get your child back on the road — with more power and longer playtime — as quickly as possible.
What You'll Need
- The TOBBI 12.5Ah Lithium Battery
- A Phillips-head screwdriver
- Your child's 12V TOBBI ride-on car
- 5–10 minutes of your time
Step-by-Step Installation Guide
Step 1: Power Off the Ride-On Car
Before doing anything, make sure the ride-on car is completely powered off. Turn the main power switch to the OFF position and remove the key if your model has one. Safety first!
Step 2: Locate the Battery Compartment
On most TOBBI 12V ride-on cars, the battery compartment is located under the seat or in the front hood area. Refer to your car's manual if you're unsure. Common models and their battery locations include:
- TOBBI 12V Bumper Car – under the seat panel
- TOBBI 12V Police Car – under the seat
- TOBBI 12V Dump Truck – under the truck bed
- TOBBI 12V Land Rover – under the hood
- TOBBI 12V Lamborghini Sian – under the hood
- TOBBI 12V School Bus – under the seat
- TOBBI 12V Tractor with Trailer – under the seat
- TOBBI 12V Off-Road UTV – under the seat
- TOBBI 12V 2-Seater Off-Road Police Car – under the seat
- TOBBI 12V Kids Ride On Truck – under the hood
- TOBBI 12V Ride-On Toy Airplane – under the body panel
- TOBBI 12V Ride-On Dump UTV – under the seat
- TOBBI 12V Aprilia Motorcycle – under the body
- TOBBI 12V Dirt Bike – under the body panel
- TOBBI 12V Bumper Car Duo Pack – under the seat panel
Step 3: Remove the Old Battery
Use your Phillips-head screwdriver to remove any screws securing the battery compartment cover. Carefully lift out the existing battery. Take note of how the wiring connectors are attached — you can take a quick photo with your phone for reference.
Step 4: Disconnect the Old Battery Connectors
Gently unplug the battery connector from the car's wiring harness. Most TOBBI ride-on cars use a standard T-style or Tamiya-style connector that simply pulls apart. Do not cut any wires.
Step 5: Connect the TOBBI Lithium Battery
Take your new TOBBI 12.5Ah Lithium Battery and plug its connector into the car's wiring harness. The connectors are designed to be plug-and-play — they will only connect in the correct orientation, so don't force them.
Step 6: Place the Battery in the Compartment
Carefully position the lithium battery in the battery compartment. The TOBBI lithium battery is designed to fit the same footprint as the original battery, so it should sit securely in place.
Step 7: Secure the Compartment Cover
Replace the battery compartment cover and tighten the screws. Make sure everything is snug and no wires are pinched.
Step 8: Power On and Test
Turn the power switch to ON, insert the key if applicable, and give the car a quick test. You should notice the car responds with full, consistent power right away. That's the lithium difference!
Tips for Best Performance
- First charge: Before the first use, charge the new lithium battery fully to activate maximum capacity.
- Storage: If storing the car for more than a month, charge the battery to about 50–60% to preserve cell health.
- Avoid deep discharge: Try not to run the battery completely flat regularly — this extends its lifespan significantly.
- Keep it dry: Store and charge the battery in a dry, room-temperature environment.
Ready to Upgrade?
The installation is simple, the results are immediate, and your child will love the extra playtime. Get the TOBBI DIY Lithium Battery Replacement – 12.5Ah today and transform your child's ride-on experience.
Browse all compatible TOBBI 12V ride-on cars below and find the perfect match for your little driver!
